 |
|
|
|
|
|
|
MC-4A
Dental
Electrosurgical
Unit
|
|
|
|
|
|
Dental
Electrosurgery's most advanced technology
The
MC-4A's unit
lacks the pure CUT feature of the Radiosurge and
is therefore not recommended for implant exposure
of biopsy. However, all the other virtues of the
Radiosurge are incorporated; isolated output,
full operating room safety testing by CSA, and
precision operation. The MC4A provides a SURGE
mode for incision an excision with pronounced
concurrent homeostasis, and a COAG mode for pin-point
accurate coagulation. Safe and effective for bipolar
forceps coagulation in wet fields and around exposed
bone. Simple to learn and operate as well as cost
effective, the MC4A is ideal for the occasional
uses encountered in Orthodontics, Periodontics
and General restorative dentistry. The isolated
output means that the instrument will not work
without the dispersive plate. The unit comes with
a 5 year warranty, "Flexi-plate" dispersive
plate, 5 "Ultra-flex" electrodes, and
an Owner's Manual. IEC 60601-1-2 EMC compliance
make this instrument as friendly as possible around
other equipment.
|
|
Exclusively
at MACAN
"Spark-Free" Technology* Modern
dental practice involves gingival tissue management
as a part of the restorative process to a degree
never before seen.
The MC-4A "spark-free" technology, which
incorporates RF band pass filtration, adds significantly
to patient comfort by eliminating spark induced
sensations and helps to reduce the risk of tissue
recession necessary for successful immediate impressions
in crown preparation, crown lengthening, and other
aesthetically critical procedures, by significantly
reducing collateral heat production.*This technology
is used in ophthalmic coagulators where very tight
control of coagulum is critical.
Floating
Return Technology Floating
return technology now brings to the dental suite
the electrical safety common to operating room
general surgery units, and also allows the safe,
effective application of bipolar coagulation without
taking the extra ordinary precautions required
for ground referenced machines
Surgical
mode allows incision with pronounced effective
concurrent hemostasis.
Coag
Mode provides exceptional coagulation with monopolar
ball Electrode
or optional bipolar forceps.
|
|
MC-4A
ELECTROSURGERY TECHNICAL SPECIFICATIONS
|
| IEC
CLASSIFICATION class 1 medical, high frequency
surgical, non-ionizing radiation device |
| CONFIGURATION
monopolar, isolated output, type BF ports |
| OPERATING
MODES |
SURGE |
50%
cut 50% coag blended 50 watts into 100ohms +10%-5%,
crest factor 1.9 Modulation : 2xline frequency,
100 or 120Hz, sinosoidal |
| |
COAG |
50%
duty cycle 25 watts into 100ohms +10%-5%, crest
factor 2.6 Modulation : line frequency, 50 or 60Hz,
sinosoidal |
| OUTPUT
VOLTAGE 500V p-p (.5kVp p-p), open load, SURGE
mode |
| SOURCE
IMPEDANCE 500ohms, nominal |
| OPERATING
FREQUENCY 3.0mHz +/-5%, nominal |
| POWER
CONTROL manual analog, continuously variable |
| OPERATIONAL
DUTY CYCLE 10 seconds ON, 20 seconds OFF (not
electronically enforced) |
| TEMPERATURE
RANGE -20C to +85C storage, OC to +40C operating,
<80% RH non condensing |
| COOLING
convection |
| SPALSH
RATING IPO |
| ACTUATION
single foot pedal (isolated low voltage circuit,
IP20 splash resistant rust proof plastic pedal)
|
| DISPERSIVE
MONITOR N/A |
| ACTIVE
INDICATION LED light, tone (defeatible) |
| POWER
REQUIRMENTS |
120V
60Hz, +/-10%, 240watts maximum consumption |
| |
230V
50HZ, +/-10%, 240VA maximum consumption |
| |
NOTE:
field selection of operating voltage requires a
skilled technician |
| SIZE
AND WEIGHT |
8.5"w,
3.5"h, 5.75"d, not including controls
and jacks 5.5pounds (9 pound shipping) |
| |
21,6cm
w; 8.89cm h; 14.6cm d; not including controls and
jacks 2.5kg (4.1kg shipping) |
| WARRANTY
5 years (exclusive of accessories) |
|
Notified
Body: Canadian Standards Association |
|
Standard:
CAN/CS C22.2 No. 601.1-M90 |
|
Mark:
C/US mark registration number 222103 |
|
Tested
to:
|
IEC
60601-1-1 Medical Safety |
|
IEC
60601-1-2 Electromagnetic Compatibility |
|
IEC
60601-1-2 High Frequency Surgical Particular Standards |
|
5
YEAR WARRANTY The
Macan MC-4A Unit is unconditionally guaranteed
for five years from the date of purchase, (exluding
handpiece, dispersive plate, cords and electrodes).
A copy of your invoice, showing the serial number
and date of purchase is all the evidence required
to implement service. Additional terms may apply.
Ask your dealer for complete information.
|
|
Electrodes

|
Dispersive
Plate and Cord

|
Handpiece
and Cord

|
Forceps
|
|
|
|
Macan Engineering & Manufacturing Company
1564 N. Damen Avenue, Chicago, IL. 60622 - U.S.A
Phone: (773) 772 - 2000 or Toll free: (866) 622- 2611
Fax: (773) 772 - 2003
|
|
|
|
 |
 |
|
|